
M 1 6 0 3 S A U   >   1 1 / 1 9 9 5    FUJITSU
NO MORE PRODUCED                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 3.5"/SLIMLINE         Cylinders    3456|     |     |
Capacity form/unform   544/      MB        Heads           3|     |     |
Seek time   / track  10.0/ 3.0 ms          Sector/track     |     |     |
Controller           SCSI2 SI/FAST         Precompensation
Cache/Buffer           512 KB FIFO RING    Landing Zone
Data transfer rate    6.000 MB/S int       Bytes/Sector      512
                     10.000 MB/S ext SYNC
Recording method                                    operating  | non-operating
                                                  -------------+--------------
Supply voltage     5/12 V       Temperature *C         5 55    |    -40 60
Power: sleep              W     Humidity     %         8 80    |      5 95
       standby            W     Altitude    km    -0.300  3.000| -0.300 12.000
       idle               W     Shock        g         5       |    505
       seek               W     Rotation   RPM      5400
       read/write         W     Acoustic   dBA        38
       spin-up            W     ECC        Bit
                                MTBF         h     800000
                                Warranty Month        24
Lift/Lock/Park     YES          Certificates                                  

**********************************************************************
                        L   A   Y   O   U   T
**********************************************************************
FUJITSU  M1603S/1606S AFTER NOVEMBER 1995  JUMPER SETTING

  +---------------------------------------------------------+
  |                                                         |XXI
  |                                              CNH1----+  |XXN
  |                                                 +----+  |XXT
  |                              +--+                       |XXE
  |                              +--CN6                     |XXR
  |                                                         |XXF
  |                                                         |XXA
  |                                                 +--+    |XXC
  |                                                 +--CNH3 |XXE
  |                                                         |XX
  |                                                         |XX
  |                                                         |XX
  |                                                         |XX
  |  +-1                                                    |
  |  +-+CN5                                                 |XX Power
  |                 After 11/1995                           |XX
  +---------------------------------------------------------+



**********************************************************************
                      J   U   M   P   E   R   S
**********************************************************************
FUJITSU  M1603S/1606S AFTER 11/95  JUMPER SETTING

 Jumper Setting
 ==============

 x = Factory default setting


 CNH1  SCSI ID
 -------------
   +----------+-----------------------+
   | SCSI ID  |        Jumpers        |
   |          | 5-6   | 3-4   | 1-2   |
   +----------+-------+-------+-------+
   |    0     | OPEN  | OPEN  | OPEN  |
   +----------+-------+-------+-------+
   |    1     | OPEN  | OPEN  | CLOSED|
   +----------+-------+-------+-------+
   |    2     | OPEN  | CLOSED| OPEN  |
   +----------+-------+-------+-------+
   |    3     | OPEN  | CLOSED| CLOSED|
   +----------+-------+-------+-------+
   |    4     | CLOSED| OPEN  | OPEN  |
   +----------+-------+-------+-------+
   |    5     | CLOSED| OPEN  | CLOSED|
   +----------+-------+-------+-------+
   |    6     | CLOSED| CLOSED| OPEN  |
   +----------+-------+-------+-------+
   |x   7     | CLOSED| CLOSED| CLOSED|
   +----------+-------+-------+-------+

 NOTE
 Always ensure that the device ID selected is unique to the SCSI bus.


 CNH1 Spindle Motor Control
 --------------------------
 Pins 7-8  OPEN   Spindle motor controlled by START/STOP command
          xCLOSED Spindle motor on at power up


 CNH1 Synchronous Data Transfer Mode
 -----------------------------------
 Pins 9-10 CLOSED Synchronous Data Transfer Mode disabled (default)
           OPEN   Synchronous Data Transfer Mode enabled



 CNH1 Reselection retry
 ----------------------
 Pins 11-12 CLOSED Reselection retry = unlimited (default)
            OPEN   Reselection retry = 10 times


 CNH1 NOT USED
 -------------
 Pins 13-14 NOT USED!


 CNH1 Active termination
 -----------------------
 Pins 15-16 CLOSED Active termination enabled (default)
            OPEN   Active termination disabled


 CN6 Remote SCSI ID Connector
 ----------------------------
    +1-3-5-7-9+
    |o o o o o|  Side View
    |o o o o o|
    +2-4-6-8-10

       +------------+----------+
       |  PINS      | SIGNAL   |
       +------------+----------+
       |Pin 2       |-ID0      |
       +------------+----------+
       |Pin 4       |-ID1      |
       +------------+----------+
       |Pin 6       |-ID2      |
       +------------+----------+
       |Pins 1,3,5,9|GND       |
       +------------+----------+
       |Pins 7-8    |RESERVED  |
       +------------+----------+
       |Pin 10      |Spindle   |
       |            |Sync pulse|
       +------------+----------+


 CNH3 Terminal SCSI Termination Power
 ------------------------------------
 1-2 CLOSED  Power is supplied to the terminating resistor from the
 3-4 CLOSED  IDD and TERMPWR pin. Power is also supplied to the
 (default)   TERMPWR pin from the IDD. (Pin 26 of the interface)

 1-2 CLOSED  The Termpwr pin is not used. Power is supplied to the
 3-4 OPEN    IDD terminating resistor only from the IDD.

 1-2 OPEN    Power is not supplied to the terminating resistor from
 3-4 CLOSED  the IDD, only from the TERMPWR pin.


 CN5 External operator panel connector
 -------------------------------------
 Pin 01    LED(V)
 Pin 02    -LED


