
C P - 2 0 8 4    CONNER
NO MORE PRODUCED                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 2.5"/SUPERSLIMLINE    Cylinders    1096|  548|     |
Capacity form/unform    85/      MB        Heads           4|    8|     |
Seek time   / track  19.0/ 5.0 ms          Sector/track   38|   38|     |
Controller           IDE / AT              Precompensation
Cache/Buffer            32 KB LOOK-AHEAD   Landing Zone
Data transfer rate    1.500 MB/S int       Bytes/Sector      512
                      6.500 MB/S ext
Recording method     RLL 1/7                        operating  | non-operating
                                                  -------------+--------------
Supply voltage     5 V          Temperature *C         5 55    |    -40 60
Power: sleep          0.2 W     Humidity     %         8 80    |      8 80
       standby        0.4 W     Altitude    km    -0.061  3.050|        12.200
       idle           1.0 W     Shock        g        10       |    100
       seek           2.0 W     Rotation   RPM      3486
       read/write     2.0 W     Acoustic   dBA        34
       spin-up            W     ECC        Bit   22,REED SOLOMON
                                MTBF         h     150000
                                Warranty Month        15
Lift/Lock/Park     YES          Certificates     CSA,TUV,UL478,VDE



**********************************************************************
                        L   A   Y   O   U   T
**********************************************************************
CONNER   CP2084  PRODUCT MANUAL 00501-008

  +------------------------------------------------------+
  | +-+                                                  |X44
  | | |                                          +++   I |XX Power
  | | |                                         S+++D  N |XX +5V 41/42
  | +-+                                         M+++C  T |XX GND 43
  |                                                    E |XX
  |                                                    R |XX
  |                                                    F |X* Position
  |                                                    A |XX 20-Key
  |                                                    C |XX
  |                                                    E |XX
  |                                                      |XX
  |                                                      |XX
  |                                                      |1X
  |                                                      |XX Factory
  |                                                      |XX test
  +------------------------------------------------------+   points




**********************************************************************
                      J   U   M   P   E   R   S
**********************************************************************
CONNER   CP2084  PRODUCT MANUAL 00501-008

 Jumper setting
 --------------

 Interface Connector/Signal Levels
 ---------------------------------
 All signal levels are TTL compatible. A logic "1" is > 2.0 Volts. A
 logic "0" is from 0.00 Volts to 0.70 Volts. The drive capabolity of
 each of the inbound signals is described below.

    +--------------------------------------------------------+
    | Pin    Signal             Pin     Signal               |
    +--------------------------------------------------------+
    | 01     -Reset             02      GND                  |
    +--------------------------------------------------------+
    | 03     +Data  7           04      +Data  8             |
    +--------------------------------------------------------+
    | 05     +Data  6           06      +Data  9             |
    +--------------------------------------------------------+
    | 07     +Data  5           08      +Data 10             |
    +--------------------------------------------------------+
    | 09     +Data  4           10      +Data 11             |
    +--------------------------------------------------------+
    | 11     +Data  3           12      +Data 12             |
    +--------------------------------------------------------+
    | 13     +Data  2           14      +Data 13             |
    +--------------------------------------------------------+
    | 15     +Data  1           16      +Data 14             |
    +--------------------------------------------------------+
    | 17     +Data  0           18      +Data 15             |
    +--------------------------------------------------------+
    | 19     GND                20      Key                  |
    +--------------------------------------------------------+
    | 21     Reserved           22      GND                  |
    +--------------------------------------------------------+
    | 23     -IOW               24      GND                  |
    +--------------------------------------------------------+
    | 25     -IOR               26      GND                  |
    +--------------------------------------------------------+
    | 27     IOCHRDY            28      MASTER/SLAVE  *      |
    +--------------------------------------------------------+
    | 29     Reserved           30      GND                  |
    +--------------------------------------------------------+
    | 31     +IRQ               32      -IO16                |
    +--------------------------------------------------------+
    | 33     +ADDR 1            34      -PDIAG               |
    +--------------------------------------------------------+
    | 35     +ADDR 0            36      +ADDR 2              |
    +--------------------------------------------------------+
    | 37     -CS0               38      -CS1                 |
    +--------------------------------------------------------+
    | 39     -Active            40      GND                  |
    +--------------------------------------------------------+
    | 41     5 Volts (Logic)    42      5 Volts (Motor)      |
    +--------------------------------------------------------+
    | 43     GND                44      Reserved             |
    +--------------------------------------------------------+
    * Provides the same function as Jumper M/S. -Master/+Slave
      should be selected at this pin or at Jumper M/S, but not both.
      This line is pulled high internally.


 MS/CD   Master/Slave
 --------------------
      M/S  C/D    For Master (C Drive) when M/S is CLOSED, place
      +-+         Jumper as shown.
      |*|  *
      |*|  *
      +-+

      M/S  C/D     If Master/Slave feature is selected at Pin 28 of
       *   *       the interface/power connector, jumper M/S should
      +-----+      be left open as ashown.
      |*   *|
      +-----+


 The CP2084 drive is designed to operate either as a Master drive (C
 Drive) or a Slave Drive (D Drive). This feature is dependent on two
 drive settings; the status of hardware Jumper M/S and the firmware
 setting of a feature bit. When (M/S) is closed, and the feature bit
 is set, the drive will assume the role of a Master Drive.
 When (M/S) is open, and the feature reset, the drive will act as the
 Slave. In single drive configurations M/S must remain in the closed
 position.

 When two drives are daisy chained on the interface, commands are
 written in parallel to both drives, only the selected drive will
 execute the command, except for the diagnostic command. In that case,
 both drives execute the command and the slave reports its status to
 the master via -HOST -PDIAG signal. Drives are selected by the DRV
 bit in the drive/head Register and by a jumper, on the drive design-
 ating it as either a master or slave. When the DRV bit is reset, the
 master is selected, and when the DRV bit is set, the slave drive is
 selected. When drives are daisy chained, one must be jumpered as the
 master and one as the slave. When a single drive is attached to the
 interface, it must be jumpered as the master. Throughout this
 document, drive selection always refers to the state of the DRV bit,
 and position of the master/slave jumper.

 Alternatively, the MASTER/SLAVE feature can be selected at pin 28 of
 the interface connector. If this is done then jumper M/S should be
 left open.



**********************************************************************
                      I   N   S   T   A   L   L
**********************************************************************
CONNER   CP2084  PRODUCT MANUAL 00501-008

 Notes on installation
 =====================

 Installation direction
 ----------------------

     horizontally                           vertically
   +-----------------+             +--+                       +--+
   |                 |             |  +-----+           +-----+  |
   |                 |             |  |     |           |     |  |
 +-+-----------------+-+           |  |     |           |     |  |
 +---------------------+           |  |     |           |     |  |
                                   |  |     |           |     |  |
                                   |  |     |           |     |  |
 +---------------------+           |  +-----+           +-----+  |
 +-+-----------------+-+           +--+                       +--+
   |                 |
   |                 |
   +-----------------+

 The drive will operate in all axis (6 directions).


 Recommended Mounting Configuration
 ----------------------------------
 This CP2084 is designed to be used in applications where the unit
 may experience shock and vibrations at greater levels than larger
 and heavier disk drives.

 The design features which allow greater shock tolerance are the use
 of rugged heads and media, a dedicated landing zone, closed loop
 servo positioning and specially designed motor and actuator
 assemblies.

 Four (4) side mounting points and four (4) bottom mounting points are
 provided to the customer. The drive is mounted using 3mm x 0.5mm
 thread screw. The screw insertion depth should not exceed 4mm into
 the mounting holes. The system integrator should allow ventilation
 to the drive to ensure reliable drive operation over the operating
 temperature range.

 For additional vibration isolation, an external suspension system
 may be used.


 Interface Connector
 -------------------
 The CP2084 drive has a 44 pin right angle interface/power connector
 mounted on the PCB. The recommended mating connector is DuPont part
 number 69764-044 or equivalent. The maximum cable lenght is two
 feet.

 Diagnostic Routines
 -------------------
 The microprocessor performs diagnostics upon application of power.
 If an error is detected the drive will not come ready.

 Magnetic Field
 --------------
 The externally induced magnetic flux density may not exceed 6 gauss
 (DC - 700KHz) or 1.0 gauss (700KHz - 1.5MHz) as measured at the
 drive surface.


 Acoustic Sound Emission
 -----------------------
 Pressure: The sound pressure level for the operating drive will not
 exceed 34 dB(A) max. at a distance of 1 meter from the drive.



**********************************************************************
                      F   E   A   T   U   R   E  S
**********************************************************************
CONNER   CP2084  PRODUCT MANUAL 00501-008

 Key Features
 ------------
 The CP2084 is a newest addition to a family of high performance 2.5
 inch low-profile disk drives with formatted capacity 85.2 megabytes.
 The drive has a 19 ms average seek time and is designed to operate
 on IBM PC/AT or equivalent computers. The drives feature a low 5V
 power requirement and high shock resistance, enabling battery
 operation in a portable environment.

 - 2.5" Form factor

 - Single 5 Volt supply

 - Low power requirements

 - 7 oz unit weigth

 - High performance rotary voice coil actuator with embedded servo
   system.

 - Single connector for power & interface

 - Run length limited code (one of seven)

 - High shock resistance

 - Internal air filtration system

 - Sealed HDA

 - Automatic actuator latch over data free landing zone during standby
   mode or power-down

 - Microprocessor-controlled diagnostics routines that are auto-
   matically executed at start-up.

 - Automatic error correction and retries

 - Block size 512 bytes

 - PC AT Interface

 - 1:1 sector interleave

 - Automativ read look ahead

 - 32K Buffer

 - Master/Slave



 Universal Translate Mode
 ------------------------
 Conner has established a Universal Translate Mode which enables the
 user to configure the drive in an AT environment to any cylinder,
 head, and sector configuration desired. The translate configuration
 is limited only by the maximum capacity of the drive. Upon initial
 power up to the drive it will default to a predetermined configura-
 tion shown below:

          Cylinders        Heads       Sectors
 CP-2084     548             8           38

 After the drive is ready, the host system may issue INIT DRIVE PARMS
 COMMAND (command code 91H) to alter the translate configuration
 (number of heads and number of sectors per track). The drive para-
 meters will then be saved in EEPROM for subsequent drive operations.


 Seek Times
 ----------

       +----------------------------------+--------+
       |Physical track to track      max. |   5 ms |
       |Logical                      max. |  10 ms |
       +----------------------------------+--------+
       |               Average msec. typ. |  19    |
       |               Average msec. max. |  40    |
       +----------------------------------+--------+
       |Latency                msec. avg. |   8.7  |
       +----------------------------------+--------+
       The timing is measured through the interface with the drive
       operating at nominal DC input voltages. The timing also assumes
       that:
             - BIOS and PC system hardware dependency have been
               subtracted from timing measurements.

             - The drive is operated using its translation parameters.


       The average seek time is determined by averaging the seek time
       for a minimum of 1000 seeks of random length over the surface
       of the disk.


 Functional Description
 ----------------------
 The CP2084 contains all necessary mechanical and electronic parts to
 interpret control signals, position the recording heads over the
 desired track, read and write data, and provide a contaminant free
 environment for the heads and disks.


 Read/Write and Control Electronics
 ----------------------------------
 One integrated circuit is mounted within the sealed enclosure in
 close proximity to the read/write heads. Its function is to provide
 head selection, read preamplification, and write drive circuitry.

 The microprocessor-controlled circuit card provides the remaining
 electronic functions which include:

        - Read/Write Circuitry
        - Rotary Actuator Control
        - Interface Control
        - Spin Speed Control
        - Dynamic Braking
        - Power Management

 A microprocessor performs diagnostics upon application of power. If
 an error is detected the drive will not come READY. At power down or
 the start of STANDBY MODE or SLEP MODE the heads are automatically
 retracted to the inner diameter of the disk and are latched and
 parked on a landing zone that is inside the data tracks.


 Drive Mechanism
 ---------------
 A brushless DC direct drive motor rotates the spindle at 3486 RPM.
 The motor/spindle assembly is dynamically balanced to provide minimal
 mechanical run-out to the disks and to reduce vibration of the HDA. A
 dynamic brake is used to provide a fast stop to the spindle motor
 and return the heads to the landing zone inside the data tracks
 when power is removed or upon initiation of STANDBY MODE.


 Air Filtration System
 ---------------------
 Within the sealed enclosure, a 0.3 micron filter which provides a
 clean environment for the heads and disks.


 Head Positioning Mechanism
 --------------------------
 The read/write heads for the CP2084 is supported by a mechanism
 coupled to the voice coil actuator.


 Read/Write Heads and Disks
 --------------------------
 Data is recorded on 65mm diameter thin film disk through micro-
 miniature thin film or MIG heads.

 The drive is designed to be used in applications where the unit may
 experience shock and vibrations at greater levels than larger and
 heavier disk drives.


 Error Correction
 ----------------
 The CP2084 drive use a Reed-Solomon code to perform error detection
 and correction. The error correction polynominal is capable of
 correcting one error burst with a maximum of 22 bits or 2 error
 bursts of up to 11 bits each, per 512 byte block. Single bursts of
 11 bits or less are corrected with no performance degradation.


 Reliability and Maintenance
 ---------------------------
 MTBF                     150,000 hours POH (population is min. of 100
                          units)
 MTTR                     10 minutes typical
 Preventive Maintenance   None
 Component Design Life    5 years


 Safety Standard
 ---------------
 The CP2084 disk drive is designed to comply with relevant product
 safety standards such as:

 - UL 478, 5th edition, Standard for Safety of Information Processing
   and Business Equipment, and UL 1950, Standard for Safety of
   Information Technology Equipment

 - CSA 22.2#154, Data Processing Equipment and CSA 22.2#950, Safety
   of Information Technology equipment and CSA 22.2#220, Information
   Processing and Business Equipment

 - IEC 380, Safety of Electrically Energized Office Machines, and
   IEC 950, Safety of Information Technology Equipment Including
   Electrical Business Equipment

 - VDE 0805 TIEL 100, Equivalent to IEC 950, and VDE 0806, Equivalent
   to IEC 380

 - TUV Essen
   TUV Rheinland


