
A C - 1 6 0    WESTERN DIGITAL
NO MORE PRODUCED                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 3.5"/SLIMLINE         Cylinders     980| 1024|     |
Capacity form/unform    63/      MB        Heads           2|    7|     |
Seek time   / track  15.0/ 6.0 ms          Sector/track     |   17|     |
Controller           IDE / AT              Precompensation
Cache/Buffer            32 KB STATIC RAM   Landing Zone
Data transfer rate    1.875 MB/S int       Bytes/Sector      512
                      6.000 MB/S ext
Recording method     RLL 2/7                        operating  | non-operating
                                                  -------------+--------------
Supply voltage     5/12 V       Temperature *C         5 50    |    -40 60
Power: sleep          1.3 W     Humidity     %         8 80    |      5 95
       standby        1.3 W     Altitude    km    -0.305  3.048| -0.305 12.192
       idle           2.9 W     Shock        g        10       |     75
       seek           4.9 W     Rotation   RPM      3605
       read/write     4.4 W     Acoustic   dBA        41
       spin-up        8.7 W     ECC        Bit   56
                                MTBF         h     100000
                                Warranty Month        24
Lift/Lock/Park     YES          Certificates     CSA,FCC,IEC950,TUV,UL1950



**********************************************************************
                        L   A   Y   O   U   T
**********************************************************************
WESTERN  CAVIAR WDAC160/WDAC2120  TECHNICAL REFERENCE MANUAL S0477 2/9






                         J2                    J8     J1
    +39------------------------------------1--5-3-1++-------+
    |o o o o o o o o o o o o o o o o o o o o  o o o||O O O O|
    |o o o o o o o o o o   o o o o o o o o o  o o o||4 3 2 1|
  --+40------------------------------------2--6-4-2+++-+-+-++----
                                                     | | | +12V
                   (Pin 20 keyed)                    | | +- GND
                                                     | +--- GND
                                                     +----- +5V


 NOTE
 For Caviar AC160/AC2120 drives manufactured before 4/1/92, connector
 J3 is rotated 180* from the position shown below.



**********************************************************************
                      J   U   M   P   E   R   S
**********************************************************************
WESTERN  CAVIAR WDAC160/WDAC2120  TECHNICAL REFERENCE MANUAL S0477 2/9

 Jumper setting
 ==============

 J8  Master/Slave Configuration
 ------------------------------

    +5-3-1+ Single Drive              +5-3-1+ Master Drive
    |o o o| Configuration             |X o o| Configuration
    |o o o|                           |X o o| (Dual Drives)
    +6-4-2+                           +6-4-2+


    +5-3-1+ Slave Drive
    |o X o| Configuration
    |o X o| (Dual Drives)
    +6-4-2+


 The Caviar drive has a jumper block (J8) located next to the 40-pin
 connector on the drive. If you are installing the Caviar drive as the
 only intelligent drive in the system, you do not need to install
 jumpers on the J8 connector. This is considered a standard single
 drive installation, and no jumpers are required.

 NOTE
 Even with no jumpers installed, the Caviar checks the DRIVE ACTIVE/
 SLAVE PRESENT (DASP) signal to determine if a slave intelligent drive
 is present.

 If you have a dual installation (two intelligent drives), you must
 designate one of the drives as the master and the other as the slave
 drive. The jumper pins on J8 connector need to be configured for the
 dual installation.

 To designate the intelligent drive as a master, place a jumper shunt
 on pins 5-6. With the Caviar configured as the master drive, the
 Caviar assumes that a slave drive is present. The jumper on pins 5-6
 is optional if the slave drive follows the same protocol as the
 Caviar (Common Access Method AT Bus Attachment).

 To designate the intelligent drive as the slave, place a jumper shunt
 on pins 3-4. When the Caviar is configured as the slave drive, the
 Caviar delays spin up for three seconds after power up reset. This
 feature prevents overloading of the power supply during power up.



**********************************************************************
                      I   N   S   T   A   L   L
**********************************************************************
WESTERN  CAVIAR WDAC160/WDAC2120  TECHNICAL REFERENCE MANUAL S0477 92

 Notes of Installation
 =====================

 Orientation
 -----------
 The Caviar can be mounted in many different ways depending upon the
 physical design of your system.


 Determining Your Configuration
 ------------------------------
 You can configure the Caviar in one of two ways:

 1. The drive is cabled directly to a 40-pin connector on the mother-
    board.

 2. The drive is cabled to an adapter card mounted in one of the
    expansion slots in the computer.

 Both configurations use a 40-pin host interface cable.

 If you are using the Caiar drive as one of two hard disk drives in
 the computer (dual installation), you may use either configuration.
 In dual installations, you must use a 40-pin host interface cable
 with three connectors and daisy-chain the two drives to the mother-
 board or adapter card.


 Dual Installations
 ------------------
 Dual Installations require a master/slave drive configuration, where
 one drive is designated as the promary (master) drive and the other
 is designated as the secondary (slave) drive. The Caviar drive is
 compatible in dual installations with other intelligent drives that
 support a master/slave configuration. The Caviar drive is not
 compatible with ST-506 drives.

 If your installation requires the ue of an adapter card, it is useful
 to know that you may also be able to connect your floppy drive(s) to
 the adapter card.


 Mounting the Drive
 ------------------
 For dual installations, it is usually easier to completely install
 one intelligent drive in the lower position first. The order of
 intelligent drives is unimportant if you are using to Western Digital
 drives. As explained previously, one must be jumpered as the master
 drive and the other as the slave drive. When installation is complete
 he drives are daisy-chained together.


 Cabling and Installation Steps
 ------------------------------
 Make sure your interface cable is no longer than 18 inches to
 minimize the noise which is induced on the data and control buses.
 Also, if you are connecting two drives together, you need a daisy-
 chain cable that has three 40-pin connectors.

 Caution: You may damage the Caviar drive if the interface cable is
 not connected properly. To prevent incorrect connection, use a cable
 that has keyed connectors at both the drive and host ends. Pin 20
 has been removed from J2 connector. The female connector on the
 interface cable should have a plug position 20 to prevent incorrect
 connection.

 Make sure that pin 1 on the cable is connected to pin 1 on the
 connectors.

 If you mount two drives in a system use a Y-Adapter for power supply.


 Installing the Adapter Card
 ---------------------------
 If you are installing the Western Digital adapter card, configuration
 will probably be unnecessary. You only need to change the default
 jumper settings if you want to disable the floppy drive controller or
 set an alternate address at 370-377.

 If you need to change the adapter card configuration, do so before
 attaching any cables or installing the card into the slot.

 NOTE
 Remove or disable any existing floppy controller which is being re-
 placed by the adapter card/floppy controller.


 Mounting Screws
 ---------------
 bottom: 6-32 UNC-2B, 0.188 max. deep
 side:   6-32 UNC-2B, 0.250 max. deep

 CAUTION
 Screws which are too long will damage board components. The screw
 must engage no more than six threads (3/16 inch).


 Power Connectors and Cables
 ---------------------------
 Power Connector:           4-pin MOLEX P/N 15-24-4041 or equivalent
 Mating Connector:          Body AMP 1-480424-0 or equivalent
                            Pins AMP 60619-4 or equivalent
 Power Cable Wire Gauge     18 AWG


 Buffer RAM
 ----------
 A 32-Kbyte (optional 64-Kbyte) static RAM buffer enhances data
 throughput by buffering sector data between the Caviar and the AT
 system bus. The RAM only buffer read/write data and ECC information.
 The buffer is accessed by two channels, each having a separate 15-bit
 address and byte-count register. The channels operate simultaneously,
 accepting read and write operations from two data paths.


 Spindle Motor
 -------------
 The spindle motor assembly consists of a brushless three-phase motor,
 spindle bearing assembly, disk mounting hub and a ferrofluid magnetic
 seal. The entire spindle motor assembly is completely enclosed in the
 HDA and bolted to the base casting. The motor rotates the spindle
 shaft at approximately 3600 RPM.

 Proprietary spindle electronics sense motor speed and angular
 position by monitoring the spindle motor's back electromotive force
 (BEMF). Using BEMF sensing, instead of the Conventional Hall effect
 ot inductive motor position sensors, lowers the power consumption and
 increases reliability. Motor driver circuits ynamically brake the
 spindle during motor spin down.


 Translation
 -----------
 The Caviar implements linear address translation. The translation
 mode and translated drive configurations are selected by using the
 Set Drive Parameters command to issue head and sector/track counts to
 the translator. Caviar supports universal translation, therefore, any
 valid combination of cylinder, head and SPT can be assigned to the
 drive, as long as the total number of sectors is not greater than the
 physical limits. The product of the cylinder, head and sectors/track
 counts must be equal to or less than the maximum number of sectors
 available to the user.

 The maximum number of sectors per drive for the Caviar AC160 and the
 AC2120 are 122,091 and 244,182 respectively. Each sector consists of
 512 bytes.

 The minimum value for any translation parameter is one. The maximum
 value for any translation parameter is as follows:

     Sectors/Track     255
     Heads              16
     Cylinders/drive  2048

 The values in the Sector Count Register and the SDH Register
 determine the Sectors Per Track (SPT) and heads. Regardless of the
 values of the SPT and the heads, Caviar will alwaye be in the trans-
 lation mode.



**********************************************************************
                      F   E   A   T   U   R   E  S
**********************************************************************
WESTERN  CAVIAR WDAC160/WDAC2120  TECHNICAL REFERENCE MANUAL S0477 92

 Description
 -----------
 The Western Digital Caviar intelligent disk drives are available in
 62/125 megabytes of formatted storage in a 3.5-inch form factor and
 low profile height. Designed for use in AT-compatible systems, Caviar
 is the premier storage solution that achieves unsurpassed reliability
 and optimum performance.

 Caviar features CacheFlow, Western Digital's exclusive multi-
 segmented adaptive disk caching system, which dynamically partitions
 the 32-KByte buffer and adapts during disk operations to the optimum
 caching mode to dramatically enhance read performance. To meet the
 demands of high performance 80386, 80386Sx, 80486 and 80486SX
 systems, Caviar has an average seek time of less than 15 milli-
 seconds.

 Caviar drives are preformatted (low-level) and defects are mapped out
 before shipment. Additionally Caviar features include:

 - Linear logical/physical address translation

 - Automatic head parking

 - Embedded servo control data on each track

 - DMA and Block Mode data transfers

 - Cache Flow

 - Power Conservation

 - 56-bit error correction code


 Zoned Recording
 ---------------
 The AC160/AC2120 drives employ Zoned Recording to increase the data
 density on the outer tracks of the drive. The outermost tracks
 contain 20% more sectors than the innermost tracks, thereby
 increasing the total capacity of the drive.

 The AC160 and AC2120 drives have two zones containing 48 and 40
 sectors per track.


 Voice Coil Assembly
 -------------------
 The voice coil assembly consists of an upper and lower magnetic plate
 a flat rotary coil, a bidirectional crash stop and a pivot bearing.

 The pivot assembly fits in the actuator block bore.


 Defect Management
 -----------------
 Every Caviar undergoes factory-level intelligent burn in, which
 thoroughly tests for and maps out defective sectors on the media
 before the drive leaves the manufacturing facility. Following the
 factory tests, a primary defect list is created. The list contains
 the sector cylinder and head numbers for all defects. The purpose of
 the sector/track map is to manage the reallocation of spare sectors
 and tracks after they have been assigned.


 Format Characteristics
 ----------------------
 The Caviar is shipped from the factory preformatted (low level) with
 all defects mapped out.

 In order to be compatible with existing industry standard defect
 management utility programs, the Caviar supports logical format. When
 the host issues the Format Track command, the Caviar performs a
 logical version of this command in response to the host's interleave
 table request for good and bad sector marking or assign/unassign the
 sector to/from an alternate sector.

 If the host issues the Format Track Command during normal operating
 modes, the data fields of the specified track are filled with a data
 pattern of all zeros. The interleave table identifies any bad sectors
 on a given track. The interleave table must contain all appropriate
 number of bytes of data. There are two bytes per sector for each
 entry in the interleave table. The first byte marks the sector as
 good or bad. The first byte is set to 00H to indicate a good sector
 or to 80H to indicate a bad sector or to 20H to unassign the
 alternate sector or to H40 to assign the sector to an alternate
 location. The second byte designates the logical sector ID number.


 Error Recovery
 --------------
 Caviar uses a 56-bit Error Correction Code (ECC) for automatic
 detection and correction of errors in the data field.


 Universal Data Translation
 --------------------------
 The Caviar provides a linear disk address translator to convert
 logical sector addresses to physical sector addresses which provides
 for easy installation and compatibility with numerous drive types.


 Intelligent Drive
 -----------------
 The Caviar does not require a slot-mounted controller card. The hard
 disk has the controller circuitry and 40-pin ATA IDE connector
 attached directly to the drive.


 Guaranteed Compatibility
 ------------------------
 Western Digital performs extensice testing in its Functional
 Integrity Testing Labs (FIT Lab.) to ensure compatibility with AT-
 compatible computers and standard operating system.


 Seek Time
 ---------
       +----------------------------------+--------+
       |Track-to-Track         msec. typ. |     6  |
       +----------------------------------+--------+
       |Average                msec. typ. |Sub-15  |
       |                       msec. max. |    28  |
       +----------------------------------+--------+
       |Latency                msec. avg. |   8.34 |
       |Index Pulse Period     msec.      |  16.67 |
       +----------------------------------+--------+


 Write Precompensation Register
 ------------------------------
 The Write Precompensation Register is ignored during normal write
 operations since the Caviar automatically determines the proper write
 precompensation. The contents of this register are only used by the
 Set Buffer Mode Command.



**********************************************************************
                      G   E   N   E   R   A   L
**********************************************************************
WESTERN   TIPS

 WESTERN DIGITAL 3.5-INCH DRIVES FREQUENTLY ASKED QUESTIONS
 ----------------------------------------------------------
 1) Will a Caviar drive work in my system?
   If your computer is 100% AT compatible and has either a 40-pin AT
   IDE interface on the motherboard or an IDE controller card with a
   40-pin data cable.

 2) What are the master/slave jumper settings on Western Digital
    drives?
    All Western Digital drives are configured the same. On the back of
    the drive between the 4-pin power connector and the 40-pin data
    connector, there is a jumper block J8 consisting of 6 pins.
    Western Digital hard drives are shipped with a jumper shunt in the
    neutral storage position (across pins 5 and 3) for future dual
    drive use.

 - If you are installing the Western Digital hard drive as the only
   hard drive in your system, leave the jmper shunt in the neutral
   storage posiition. Jumper shunts are not required for single hard
   drive installations.

 - To designate the Western Digital hard drive as the master (C:),
   place a jumper shunt on pins 5-6

 - To designate the Western Digital hard drive as the slave (D:),
   place a jumper shunt on pins 3-4.

 3) What are the drive type and the drive parameters in the CMOS, for
    Western Digital drives?
    On top of the drive, the number of cylinders, heads and sectors
    per track are printed on the label. Precomp and L-zone should be
    set equal to the drive's cylinder count + 1. Select user type or
    custom type (typically type 41 or 42) for your drive. This will
    allow you to type in the parameters. Older systems that do not
    offer a user type can either upgrade the system BIOS or set the
    drive to drive type 1 (which should be a smaller drive size), and
    run Ontrack Disk Manager from A drive to get the full capacity of
    the drive. If you do not follow one of these procedures and your
    system is pre-1994, you will be limited to the largest size drive
    your BIOS will allow.

 4) What is the Ontrack Disk Manager software that came with my drive
    and what does it do?
    Ontrack Disk Manager is the original hard disk installation
    package that will initialize, partition, and prepare your hard
    drive for use. Ontrack Disk Manager also allows you to access the
    full capacity of the drive even when your system BIOS can't. It is
    compatible with 32-bit disk access.

 Note: Ontrack Disk Manager must be installed from floppy drive A. If
 your A drive is a 5.25-inch floppy drive, copy the contents of your
 Ontrack Disk Manager disk to a formatted 5.25-inch disk and re-run
 Ontrack Disk Manager.

 5) I just installed Ontrack Disk Manager on my Caviar drive and tried
    to install DOS. DOS attempted to write to my drive and it
    formatted my drive back to 528 MB which is my BIOS limitation. How
    do I install DOS and still get the full capacity of my drive?
    After Ontrack Disk Manager installation, you must create an
    Ontrack Disk Manager rescue disk. There are two ways of
    accomplishing this:

 OPTION 1:
 - Create a clean DOS bootable disk.

 - Copy 2 files from the Ontrack Disk Manager disk to your bootable
   disk: XBIOS.OVL, and DMDRVR.BINs Create a CONFIG.SYS file on this
   bootable disk with these 3 lines: DEVICE=DMDRVR.BIN FILES=35
   BUFFERS=35

 - Remove the floppy and reboot the system.

 - When you see the message "Press spacebar to boot from diskette",
   press the spacebar (system halts).

 - Insert the rescue disk in the A: drive.

 - Press any key (system resumes boot process).

 - At the A: prompt, remove rescue disk, insert DOS installation disk
   and type SETUP.

 - You can now install DOS without overwriting the Ontrack Disk
   Manager files.

 OPTION 2:

 - Create a clean DOS bootable disk.

 - Insert Ontrack Disk Manager disk in the A: drive.

 - At the A prompt, type: DMCFIG/D=A:. You will be prompted to insert
   a bootable floppy in the A: drive.

 - Follow the prompts on the screen. Ontrack Disk Manager will ask you
   to change disks a few times.

 - Continue until Ontrack Disk Manager is finished.

 - Remove the floppy and reboot the system.

 - When you see the message "Press spacebar to boot from diskette".
   Press the spacebar (system halts).

 - Insert the rescue disk in A drive.

 - Press any key (system resumes boot process).

 - At A prompt, remove rescue disk, insert DOS installation disk and
   type SETUP.

 - You can now install DOS without overwriting the Ontrack Disk
   Manager files.

 6) CHKDSK or SCANDISK reports a few bad sectors. How do I go about
    fixing the problem.
    You can use the Western Digital defect management utility WDATIDE.
    One of its options is the comprehensive surface analysis. This
    procedure will mark all grown defects bad if indeed there are any
    and it will compensate for the lost capacity by utilizing spare
    tracks.

 Note: This utility is data destructive. Back up all data on the drive
 before using it. Due to the thoroughness of this operation, WDATIDE
 can take quite a bit a time depending on the capacity of your drive.

 7) Do I have to do anything with my original drive when adding a new
    drive to my system?
    Yes, one hard drive must be designated as the master drive
    (preferably the newer, faster drive) and the other must be
    designated as the slave drive. Typically, most drives need to have
    a jumper placed on them to specify the Master or Slave position.
    For information on non-Caviar hard drives, please contact the
    appropriate manufacturer.

 8) I installed my new drive and entered the drive parameters in the
    CMOS, but the drive will not boot or it displays the message "HDD
    controller failure."
    Your drive must be partitioned and formatted before it will be
    bootable. If your system will support drives larger than 528 MB,
    and you have a copy of MS-DOS or PC-DOS version 5.0 or greater,
    insert the setup diskette in your floppy drive and turn on your
    computer. Follow the prompts and DOS will partition and format the
    drive for you.

 If you do not have a copy of MS-DOS or PC-DOS version 5.0 or greater,
 you will need to boot from a bootable disk and then run the FDISK
 command to partition your drive, and then format the drive using the
 DOS FORMAT command. After running format, you should be able to
 reboot your computer from your hard drive.

 9) How can I use the full capacity of my Caviar drive of 540 MB or
    greater?
    You can use Ontrack Disk Manager to obtain full capacity if your
    system does not support LBA mode. If your system does support LBA
    mode, you can enable LBA in your CMOS setup utility.

 10) How can I get 32-Bit Disk Access in Windows on my Caviar AC2540,
     AC2700 or AC31000 in Windows 3.1x? If your BIOS supports the
     drive at full capacity (i.e., the BIOS supports Logical Block
     Addressing) you use WDCDRV.386, Western Digital's FastDisk device
     driver. This driver is contained in a file named WIN31.EXE
     available for downloading from our bulletin board (714/753-1234),
     our Web server (WWW.WDC.COM), our FTP site (FTP.WDC.COM), our
     forum on the Microsoft Network (Go word WDC), and our forum on
     America On-line (keyword WDC). If your BIOS does not support LBA
     mode and you have installed your drive using Ontrack Disk Manager
     (v6.03 and above), run DMCFIG to install WDCDRV.386 and obtain
     32-Bit Disk Access.

 11) My drive will not spin up or spins down after a few seconds.
     This is a drive failure. Return the drive to the distributor or
     contact a technical support representative to receive a Return
     Materials Authorization (RMA).

 12) CMOS, FDISK and File Manager in Windows report less than the
     capacity of my new drive, but CHKDSK reports the right number of
     bytes. Which is correct?
     Setup (CMOS) and FDISK use a binary definition of a megabyte
     which is calculated at 1,048,256 bytes per megabyte. All hard
     drive manufacturers and the DOS CHKDSK utility use a decimal
     definition of a megabyte which is calculated at 1,000,000 bytes
     per megabyte. This is why some utilities show 515 MB for a 540
     megabyte drive and some show the actual number.

 13) How Can I install OS/2 for Windows, OS/2 3.0 WARP, Windows NT
     3.5x or Windows 95 on my drive which was initially installed
     using Ontrack Disk Manager?
     If you have Ontrack Disk Manager version 6.03, 6.03a, or 6.03b,
     download the file named DMPATCH.EXE from Western Digital's online
     services: ftp site: ftp.wdc.com

 World Wide Web Site: http://www.wdc.com/
 Microsoft Network (MSN) - Go word WDC
 America Online (AOL) - Keyword: Western Digital
 Western Digital's BBS at (714) 753-1234
 This file has the latest Ontrack Disk Manager drivers which will
 allow you to install OS/2 version 2.1x, OS/2 WARP, Windows NT 3.5x
 or Windows 95 on your hard drive. Please read the included readme
 file with this file for further detail.

 14) My drive will work as a slave but not as a master (or vice-
 versa).
 Check master/slave jumpers on all drives. Also, some drive's speed
 and timing differ drastically as to the initial spinup sequence. This
 might confuse the system and cause one of the drives not to be
 recognized. The best solution for this situation is to exchange
 drives (make the master a slave and vice-versa).

 15) My drive will not partition when I run FDISK. It hangs the system
     or it displays the message: "Runtime error."
     This is usually caused by corruption or damage to track zero. Use
     the Western Digital utility WDFMT to format the drive. If that
     does not help, call Western Digital Technical support at
     1-800-ASK-4-WDC to get further instructions.

 16) Can a hard drive be mounted on it's side, edge, or upside down?
     Drives can be mounted on any side but it is preferable to mount
     the drive right side up. It is also important to use all four
     screws to hold the drive firmly in place.


 Self-Monitoring, Analysis, and Reporting Technology (S.M.A.R.T.)
 ----------------------------------------------------------------
 S.M.A.R.T. enables a drive's internal status to be monitored through
 diagnostic commands at the host level.

 The Caviar AC21600, AC32100 and AC32500 drives monitor read error
 rate, start/stop count, spin-up retry count, and drive calibration
 retry count. All of these attributes are updated and stored on the
 hard drive in the reserved area of the disk. The hard drive also
 stores a set of attribute thresholds that correspond to the
 calculated attribute values. Each attribute threshold indicates the
 point at which its corresponding attribute value achieves a negative
 reliability status.
 ====================================================================

  QUESTION
  Which hard drive specification is most important to overall
  system performance ?

 - Host Transfer Rate
 - Drive RPM (revolutions per minute)
 - Disk Transfer Rate (Media Rate)
 - Seek Time
 - Cache Size
 - PC Data Handling
 - All of the above

 Answer
 The correct answer is actually a combination of "all of the above,"
 keeping in mind most of the above specifications are interrelated
 when it comes to optimizing system performance.

 The pie chart illustrates the relative influence of factors affecting

 drive performance during a typical random I/O operation (reading
 and writing to a hard drive).

 The major determinate of hard drive performance is mechanical
 factors which are one hundred times slower than the high-speed
 electronics contained in a drive.


 Factors Affecting Hard Drive Performance
 (In their relative order of importance)

 MECHANICAL LATENCIES
 Mechanical Latencies include both Seek Time and Rotational
 Latency. The seek time is a measure (in milliseconds) of how
 fast the hard drive can move its read/write heads to a desired
 location. Rotational latency is a measure of the average time
 (also in milliseconds) the read/write heads must wait for the
 target sector on the disk to pass under them once the read/write
 heads are moved to the desired target track.

 Mechanical latencies are the main hindrance to higher performance
 in modern Enhanced IDE (EIDE) hard drives. The time delays of
 mechanical latencies are one hundred times higher than
 electronic (non-mechanical) latencies associated with the
 transferring of data. Therefore, reducing mechanical latencies
 (a lowering of seek time and rotational latency) should be the
 top consideration in improving hard drive performance.

 RPM
 This is the rotational speed of the media (disk), also referred
 to as the spindle speed. Hard drives only spin at one constant
 speed. Typical speeds are 3600 to 3880, 4500, and 5200 to 5400
 revolutions per minute. The slower the RPM, the higher the
 Mechanical Latencies. Disk RPM is a critical component of hard
 drive performance because it directly impacts the rotational latency
 and the Disk Transfer Rate explained below.

 DISK TRANSFER RATE
 The Disk Transfer Rate (sometimes called media rate) is the
 speed at which data is transferred to and from the disk media
 (actual disk platter) and is a function of the recording frequency.
 Typical units are bits per second (BPS), or bytes per second.
 Modern hard disks have an increasing range of Disk Transfer
 Rates from the inner diameter to the outer diameter of the disk.
 This is called a "zoned" recording technique.

 The key media recording parameters relating to density per platter
 are Tracks Per Inch (TPI) and Bits Per Inch (BPI). A track is a
 circular ring around the disk. TPI is the number of these tracks
 that can fit in a given area (inch). BPI defines how many bits
 can be written onto one inch of a track on a disk surface. To
 greatly simplify, the Disk Transfer Rate (the rate at which data
 is read and written to the disk) is dependent upon the speed of
 the disk (RPM) and the density of the data on the disk (BPI).
 Even most modern, high-speed, 5000 RPM hard drives are generally
 limited to a maximum Disk Transfer Rate of approximately 9 to 10
 MB per second. This specification is critical to performance and
 must be weighed carefully against such electronic latencies as
 Mode 3 PIO and Mode 4 PIO host transfer rates explained below.

 PC DATA HANDLING
 After the data moves down the IDE cable from the drive to the host
 interface, there are several factors that can affect drive
 performance over which the hard drive has no control. PC Data
 Handling is independent from the hard drive and very dependent
 upon the CPU type and speed, the BIOS overhead (how the system
 issues commands to the hard drive), speed and size of the system
 RAM and RAM cache, CPU-to-memory speed, and storage subsystem
 performance. PC Data Handling is also affected by the caching
 methods of such software applications as SMARTDRIVE, 32-bit
 disk access operating system drivers, etc.

 HOST TRANSFER RATE
 The speed at which the host computer can transfer data across the
 IDE or EIDE interface. Processor Input/Output (PIO) modes and
 Direct Memory Access (DMA) modes are defined in the ATA-2 industry
 specification as follows:

 Mode 3 PIO  11.1 MB/sec
 Mode 4 PIO  16.6 MB/sec
 Mode 1 DMA  13.3 MB/sec
 Mode 2 DMA  16.6 MB/sec

 Modern host computer systems usually support most of the above
 modes. Faster Host Transfer Rates in the future will use multi-word
 DMA modes as the industry will not support any future PIO mode
 standards beyond mode 4.

 The computer system manufacturer is responsible for implementing a
 Host Transfer Rate that is high enough to ensure that the host
 computer is not the performance bottleneck. Implementing
 increasingly higher Host Transfer Rates without corresponding
 increases in Disk Transfer Rates on the hard drive will not result
 in increased drive performance.


 Cache Buffer Size - Is Bigger Always Better ?
 A Cache Buffer is similar to a water glass. When you are writing
 to a hard drive, the host computer fills the glass and the disk
 media empties it. If you are reading data from a hard drive, the
 disk media fills the glass and the host computer empties it.

 The reason that a bigger cache buffer is not always better
 (or faster) is because the host computer (with Mode 4 PIO or
 Mode 2 DMA capabilities) can empty or fill the glass much faster
 than the hard drive can empty or fill it. When the host system can
 transfer data in or out of the cache buffer faster than the media
 rate, a larger buffer size becomes irrelevant because the host
 system is always "waiting" for the hard drive.

 Western Digital hard drives are designed with cache buffer sizes
 that are matched to the Disk Transfer Rate capabilities of the
 drive and the Host Transfer Rates of modern computer systems. All
 of our drives are benchmarked with various cache buffer sizes to
 verify that the most cost-effective and performance-effective
 cache size is implemented.


 Confusion Over Mode 4 and Mode 2 DMA
 The Enhanced IDE program created the long-range road map for
 performance enhancements which included faster disk and host
 transfers, Mode 3, Mode 4, Mode 2 DMA, etc. Currently, computer
 systems and hard drive controller silicon have most of the elements
 needed to implement Mode 4 PIO or Mode 2 DMA (a 16.6 MB/sec Host
 Transfer Rate). However, to take advantage of these performance
 modes, physical drive architecture must also make some performance
 improvements in the area of Mechanical Latencies and Disk Transfer
 Rate (media rate) as defined earlier.

 Some competitors, in their eagerness to supply a new feature, are
 prematurely marketing Mode 4 and Mode 2 DMA. While their drive
 controller silicon supports these modes (which is very easy and
 inexpensive to implement), spindle speeds (RPM), rotational latency,
 bit density, and other factors have not yet been improved (these
 being very difficult and costly). The result is hard drives which
 have the electronic capability to do Mode 4 and Mode 2 DMA transfer
 rates, but can't take advantage of these modes due to the slower
 Disk Transfer Rate of the drive.

 Western Digital will not be implementing Mode 4 or Mode 2 DMA on
 older drive products as the host systems into which these drives
 are designed are not electrically capable of these data transfers,
 nor are the Disk Transfer Rates on these drives beyond current Mode
 3 capabilities. As next generation systems are introduced, they will
 be paired with next generation drives. Those drives will require
 and offer true Mode 4 / Mode 2 DMA capability from a total drive
 architecture standpoint.
 =====================================================================
 AC2540/2635/2700/2850/21000/31000/31200/31600

 Windows 95 Operating System Addendum
 ------------------------------------
 The information in this addendum supersedes that supplied in Windows
 95 section on pages 35 and 36 of this manual. Please refer to thos
 addendum for Windows 95 questions.

 Although Windows 95 is capable of recognizing the full capacity of
 hard drives larger than 528 MB in systems with a translating BIOS,
 some restrictions apply to systems without a translating BIOS.


 For Systems With a Translating BIOS
 -----------------------------------
 Enter your CMOS setup and select a drive type that will recognize the
 full capacity of your drive. This is usually done by selecting the
 auto config drive tape. The boot partition can be set up to be as
 large as the full capacity of your hard drive.


 For Systems Without a Translating BIOS
 --------------------------------------
 Enter your CMOS setup and select a user defined drive type. Enter
 these parameters: cylinders = 1024, heads = 16, sectors = 63. Your
 system's total disk space will be limited to a maximum of 528MB.

 If you want your system to utilize more than 528 MB of disk space,
 you must use Ontrack's Disk Manager software (or a similar third-
 party installation software).


 Installing Windows 95 on a Hard Drive with Ontrack Disk Manager
 Already Installed
 ---------------------------------------------------------------
 The Windows 95 installation program will analyze your computer
 system and install seamlessly with Ontrack Disk Manager.


 Computer Systems with Windows 95 Already Installed
 --------------------------------------------------
 If you are installing a Western Digital hard drive and Ontrack Disk
 Manager on a computer system with Windows 95 already installed, you
 must install Ontrack Disk Manager as described here.

 Enter your CMOS setup and select a user defined drive type. Enter
 these parameters for drives with capacities over 528MB:
         Cylinders = 1024, Heads = 16, Sectors = 63.

 Save these changes and reboot your computer.

 1. Select the Start icon from the Windows 95 main screen.
    DO NOT open an MS-DOS menu from Win 95 to install Ontrack Disk
    Manager.

 2. Choose the Shut Down option.

 3. Select Resatrt Computer in DOS mode. When your computer restarts,
    you should be at the DOS prompt.

 4. Install Ontrack Disk Manager.

 Windows 95 will noe recognize the full capacity of your hard drive
 and run in 32-bit disk access mode for optimum performance.


